TELSAR - зарегистрированный товарный знак компании ООО «ТВБизнес»
Пассивный медный Breakout кабель прямого подключения 400G QSFP112 предназначен для использования в сетях 400GBASE Ethernet и InfiniBand (IB). QSFP112 представляет собой систему модулей и разъемов на базе текущего стандарта QSFP, разработанную для поддержки скорости 112 Гбит/с на канал в 4-канальной системе QSFP, что обеспечивает функционирование экосистемы соединений 400G QSFP. Данное решение существенно упрощает пользователям предыдущих поколений QSFP модернизацию пропускной способности каналов до 400G на порт при меньших затратах и минимальном времени перехода. Кабель обеспечивает передачу данных от каждой из двух пар медных проводников на стороне одиночного разъема QSFP112 (пары 1 и 2, 3 и 4) к соответствующим парам каждого из разъемов QSFP112 (пары 1 и 2) на многопортовой стороне.
Signal Integrity
|
ITEM |
REQUIREMENT |
TEST CONDITION |
|
|
Differential Impedance |
Cable Impedance |
100±5Ω |
Rise time of 25ps (20 % - 80 %).
|
|
Paddle Card Impedance |
100±10Ω |
||
|
Cable Termination Impedance |
100±10Ω |
||
|
Differential to common-mode (Input/Output)Return loss SCD11/SCD22] |
Return_loss(f)≥
Where f is the frequency in GHz Return_loss(f) is the Differential to common-mode return loss at frequency f |
50MHz≤f ≤40GHz |
|
|
Common-mode to Common-mode (Input/Output)Return loss SCC11/SCC22] |
Return_loss(f)≥1.8dB 0.05≤f≤40 Where f is the frequency in GHz Return_loss(f) is the common-mode to common-mode return loss at frequency f |
50MHz≤f ≤40GHz |
|
|
Differential Insertion Loss (SDD21 Max.)]
|
(Differential InsertionLoss Max. For TPa to TPb Excluding Test fixture ) |
50MHz≤f ≤40GHz |
|
|
Insertion _loss(f)≥-19.75dB 0.05≤f≤26.56 Where f is the frequency in GHz Insertion Loss (f) Differential Insertion Loss at frequency f |
|||
|
Differential to common-mode Conversion Loss-Differential Insertion Loss(SCD21-SDD21) |
Conversion _loss(f) – IL(f)≥
Where f is the frequency in GHz Conversion_loss(f ) is the cable assembly differential to common-mode conversion loss IL(f) is the cable assembly insertion loss |
50MHz≤f ≤40GHz |
|
|
Intra Skew |
10ps/m, |
10MHz≤f ≤19GHz |
|
|
ITEM |
REQUIREMENT |
TEST CONDITON |
|
Low Level Contact Resistance |
70milliohms Max. From initial. |
EIA-364-23:Apply a maximum voltage of 20mV And a current of 100 mA. |
|
Insulation Resistance |
10Mohm(Min.) |
EIA364-21:AC 300V 1minute |
|
Dielectric Withstanding Voltage |
NO disruptive discharge. |
EIA-364-20:Apply a voltage of 300 VDC for 1minute between adjacent terminals And between adjacent terminals and ground. |
|
ITEM |
REQUIREMENT |
TEST CONDITON |
|
[Operating Temp. Range |
0°C to +70°C |
Cable operating temperature range. |
|
Storage Temp. Range (in packed condition) |
-40°C to +85°C |
Cable storage temperature range in packed condition. |
|
Thermal Cycling Non-Powered |
No evidence of physical damage |
EIA-364-32D, Method A, -25 to 90C, 100 cycles, 15 min. dwells |
|
Salt Spraying |
48 hours salt spraying after shell corrosive area less than 5％. |
EIA-364-26 |
|
Mixed Flowing Gas |
Pass electrical tests per 3.1 after stressing. (For connector only) |
EIA-364-35 Class II,14 days. |
|
Temp. Life |
No evidence of physical damage |
EIA-364-17C w/ RH, Damp heat 90℃ at 85% RH for 500 hours then return to ambient |
|
Cable Cold Bend |
4H,No evidence of physical damage |
Condition: -20℃±2℃, mandrel diameter is 6 times the cable diameter. |
|
ITEM |
REQUIREMENT |
TEST CONDITON |
|
Vibration |
Pass electrical tests per 3.1 after stressing. |
Clamp & vibrate per EIA-364-28E, TC-VII, test condition letter – D, 15 minutes in X, Y & Z axis. |
|
Cable Flex |
No evidence of physical damage |
Flex cable 180° for 20 cycles (±90° from nominal position) at 12 cycles per minute with a 1.0kg load applied to the cable jacket. Flex in the boot area 90º in each direction from vertical. Per EIA-364-41C |
|
Cable Plug Retention in Cage |
90N Min. No evidence of physical damage |
Force to be applied axially with no damage to cage. Per SFF 8661 Rev 2.1 Pull on cable jacket approximately 1 ft behind cable plug. No functional damage to cable plug below 90N. Per SFF-8432 Rev 5.0 |
|
Cable Retention in Plug |
90N Min. No evidence of physical damage |
Cable plug is fixtured with the bulk cable hanging vertically. A 90N axial load is applied (gradually) to the cable jacket and held for 1 minute. Per EIA-364-38B |
|
Mechanical Shock |
Pass electrical tests Per 3.1 after stressing. |
Clamp and shock per EIA-364-27B, TC-G,3 times in 6 directions, 100g, 6ms. |
|
Cable Plug Insertion |
60N Max.(QSFP112) |
Per EIA-364-13 Test with connector, cage and module. (Latch disengaged, without heatsink) |
|
Cable plug Extraction |
30N Max. (QSFP112) |
Per EIA-364-13 Test with connector, cage and module. (Latch disengaged, without heatsink) |
|
Durability |
50 cycles,No evidence of physical damage |
EIA-364-09, perform plug &unplug cycles:Plug and receptacle mate rate: 250times/hour. 50times for QSFP28/SFP28 module (CONNECTOR TO PCB) |
| Производитель (бренд): | TELSAR |
| Применение: | Коммерческое |
| Размещение: | В слот для модулей |
| Тип: | Breakout DAC кабель |
| Форм-фактор: | QSFP-DD, QSFP56 |
| Скорость передачи данных: | 200 Гбит/с, 400 Гбит/с |
| Дальность передачи: | 1,5 м |
